ENS22-E does not show any SPI configuration available | Thales IoT Developer Community
January 14, 2020 - 1:35am, 1211 views
First, let me introduce the files I am referring to, so I can explain better the situation, as follows:
[1] - Starter Kit B80 User Guide Version: 01 DocId: Starter_Kit_B80_v01
[2] - Cinterion® ENS22-E Hardware Interface Description Version: 01.000 DocId: ENS22-E_hid_v01.000
[3] Cinterion® ENS22-E AT Command Set Version: 01.000 DocId: ENS22-E_ATC_V01.000
[4] Cinterion® ENS22-E AT Command Set Version: 02.000 DocId: ENS22-E_ATC_V02.000
- In [2], the document mentions the ASC1 being used as an SPI.
- In [2], there is the AT^SSPI command available, however, in [3], there is not AT^SSPI command listed.
- In [1], I can find the SPI pins in the pin mapping 2x40-pin connector to 80-pin board-to-board connector.
- When I enter ATI in the module, I get this output:
Cinterion
ENS22-E
REVISION 02.000
OK
- When I enter AT^SCFG=? I get this:
AT^SCFG=?
^SCFG: "GPIO/****/ASC1",("gpio","std","rsv")
^SCFG: "GPIO/****/DCD0",("gpio","std","rsv")
^SCFG: "GPIO/****/DSR0",("gpio","std","rsv")
^SCFG: "GPIO/****/DTR0",("gpio","std","rsv")
^SCFG: "GPIO/****/RING0",("gpio","std","rsv")
^SCFG: "MEOpMode/SRPOM",("0","1")
^SCFG: "MEOpMode/PowerMgmt/Suspend",("0","1")
^SCFG: "MEShutdown/sVsup/threshold",("-4"-"4")
^SCFG: "Radio/Band/4G",("0x00000004"-"0x08080094")
^SCFG: "Tcp/WithURCs",("on","off")
^SCFG: "URC/Ringline",("off","local","asc0")
^SCFG: "URC/Ringline/ActiveTime",("0","1","2")
OK
- When I enter AT^SCFG? I get this:
AT^SCFG?
^SCFG: "GPIO/****/ASC1","std"
^SCFG: "GPIO/****/DCD0","std"
^SCFG: "GPIO/****/DSR0","std"
^SCFG: "GPIO/****/DTR0","std"
^SCFG: "GPIO/****/RING0","std"
^SCFG: "MEOpMode/SRPOM","0"
^SCFG: "MEOpMode/PowerMgmt/Suspend","0"
^SCFG: "MEShutdown/sVsup/threshold","0","0"
^SCFG: "Radio/Band/4G","0x08080094"
^SCFG: "Tcp/WithURCs","on"
^SCFG: "URC/Ringline","local"
^SCFG: "URC/Ringline/ActiveTime","2"
OK
So, I cannot see any SPI mentioned in the configurations of the module. Am I missing something?
Hello,
You have revision 2 module. This revision does not support SPI and I2C interfaces unfortunately. Thre was support in revision 1. You have AT commands sets for both revisions and that's why only one has SSPI command description.
Best regards,
Bartłomiej