PHS8 - Incomplete frame | Thales IoT Developer Community
March 7, 2015 - 6:49pm, 3315 views
Hi all,
I am using the PHS8-P in an embedded enviroment. Sometimes a receive an "incomplte frame" answer from the muxer and I could not catch the problem.
Do you have any ideas, why it is happened?
Many thanks.
brgds,
Birthe
Hello,
Could you please write more details: ati1 response from the module, device and operating system that you are using with the module, driver version.
Do you have any mux log?
How is the module connected - via USB or serial. If serial, please verify if you are using power saving on serial interfaces.
Best regards,
Bartłomiej
Hi Bartlomiej,
The PHS8 is connected via serial.
Firmware version: 3.0.0.1
A-Revision: 01.000.01
WinCE 6.0
Mux Driver : 1.9 Feb 2014
Mux Log:
03.03.2015 17:18:30 <*6329921> MuxDrv: CMuxChannel::Open() m_dwDlci = 1, instance ***** 1
03.03.2015 17:18:32 <*6332486> MuxDrv: Sending AT command: AT+IPR=115200<cr>
03.03.2015 17:18:32 <*6332493> MuxDrv: Received OK response: AT+IPR=115200<cr>
03.03.2015 17:18:32 <*6332494> MuxDrv: Sending AT command: AT&S0\Q3<cr>
03.03.2015 17:18:32 <*6332498> MuxDrv: Received OK response: AT&S0\Q3<cr>
03.03.2015 17:18:32 <*6332499> MuxDrv: Sending AT command: at^sdport=2<cr>
03.03.2015 17:18:33 <*6332503> MuxDrv: Received OK response: at^sdport=2<cr>
03.03.2015 17:18:34 <*6333505> MuxDrv: Sending AT command: at^scfg="MEopMode/PwrSave","disabled"<cr>
03.03.2015 17:18:34 <*6333555> MuxDrv: Received OK response: at^scfg="MEopMode/PwrSave","disabled"<cr>
03.03.2015 17:18:35 <*6334556> MuxDrv: Sending AT command: AT+CMUX=0<cr>
03.03.2015 17:18:35 <*6334576> MuxDrv: Received OK response: AT+CMUX=0<cr>
03.03.2015 17:18:35 <*6334621> MuxDrv: Protocol-Version: Requested: 4, Supported: 4, Used: 4
03.03.2015 17:18:35 <*6334725> MuxDrv: CMuxChannel::Open() m_dwDlci = 1, instance ***** 2
03.03.2015 17:18:49 <*6348658> MuxDrv: CMuxChannel::Open() m_dwDlci = 2, instance ***** 1
03.03.2015 17:18:49 <*6348878> MuxDrv: CMuxChannel::Close() m_dwDlci = 2
03.03.2015 17:18:49 <*6348908> MuxDrv: CMuxChannel::Open() m_dwDlci = 3, instance ***** 1
03.03.2015 18:22:38 <*10178053> MuxDrv: Incomplete mux frame detected!
Thanks,
Birthe
Hello,
This means that the MUX data Frame is corrupted. This can happen when there is a data lost in the serial interface.
Still I haven't found any record in our databases regarding similar problem and the possible reasons.
Best regards,
Bartłomiej